Views: 0 Author: Site Editor Publish Time: 2026-11-11 Origin: Site
Start a transfer press line design with the part at each stage of forming. A flat blank, a drawn shell, and a trimmed part can have different dimensions, stiffness, and gripping points. The press must deliver the required force and energy where forming takes place, while the transfer system must move each intermediate shape without interference, distortion, or loss of position. Those requirements determine the line layout, equipment selection, and production rate.
Table of Contents
List the operations in order and identify the geometry that enters and leaves each station. A large housing, for example, might be drawn, redrawn, trimmed, pierced, and flanged. Record which surfaces locate the part at each station, what changes after forming, and which features remain available for handling. If a station removes a flange used for gripping, the next transfer needs a different pickup point.
Define how blanks enter and finished parts leave the line. For pre-cut blanks, include destacking, blank separation, and the location of the first pickup. For a coil-fed configuration, establish where blanking takes place and how the separated blank reaches the forming station. Plan scrap removal at the same time. Large trim scrap can interfere with transfer or force a stop if the discharge path is undersized or hard to access.
A single multistation press places multiple operations under a common slide. A tandem line distributes the work across separate presses and transfers the part between them. A common slide can simplify the overall layout when the stations fit inside one press and can share its stroke and timing. Separate presses offer more flexibility when operations require different stroke profiles, die spaces, or forming arrangements.
Design factor | Single multistation transfer press | Tandem press line |
|---|---|---|
Station layout | Multiple stations share a press bed and slide | Operations are distributed across separate presses |
Forming requirements | Check that the stations can work within a common stroke and timing profile | Evaluate the press and stroke requirements for each operation |
Part movement | Transfer occurs between stations within a common press opening | Part handling must bridge the distance between presses |
Footprint and access | Check internal clearance, die-change access, and maintenance space | Allow room for separate presses, transfer paths, and service access |
Main constraint to validate | Combined station loads, off-center loading, and transfer clearance | Synchronization, inter-press handling time, and recovery after a stop |
KINGLAN lists equipment for both layouts. Its single-press multistation manipulator is listed for moving parts between stations. Its multi-press link type manipulator is listed for linked press arrangements. Use the station layout and motion requirements to determine which equipment is worth evaluating.
| |
Build a load estimate for each operation and show where the load acts on the bed and when it occurs during the stroke. On a common-slide press, several stations can apply load during the same stroke. A heavy draw on one side and a lighter trim on the other can create an off-center load even when the total force is below the press rating. Compare the combined load distribution with the manufacturer’s permissible off-center load limits.
Ask the press supplier to check available force at the position where the load occurs and available energy at the proposed operating speed. Deep drawing can require force over a substantial part of the stroke. A press that can meet the peak force requirement may still need a different speed or configuration to meet the energy demand. Where the process uses a die cushion or ejector, include its required force, travel, and timing in the review.
Check the usable bed and slide area, die height, stroke, and clear opening with the actual die layout. Include grippers, transfer rails, scrap chutes, and the workpiece at its tallest intermediate stage. A part may fit on the press bed and still run out of clearance when lifted over a locator or die feature.
Make room for die changes and routine service. Identify the direction in which dies are loaded, where transfer equipment must retract or be removed, and how operators can reach gripper tooling, sensors, lubrication points, and scrap collection areas. Resolve those access questions before the equipment footprint is fixed.
Review part mass, center of gravity, stiffness, and permitted contact areas at each pickup. A wide blank can sag during acceleration. A deep shell may tilt if its center of gravity sits far from the gripping points. Test support and contact positions on a representative part, particularly when the drawing limits cosmetic marks or deformation.
Compare gripping methods against the actual contact surface. A vacuum pickup needs a surface that can maintain a seal under the expected handling conditions. A mechanical finger needs access to a feature it can grip consistently without damaging the part. Evaluate the complete moving load, including end-of-arm tooling, against the transfer equipment’s capacity at the planned reach and motion profile. KINGLAN’s independent manipulator is listed for handling large sheet metal parts across multiple presses.
Review the sequence from pickup to placement. Account for lifting over die features, horizontal travel, any required reorientation, settling at the next station, and gripper withdrawal before the press closes. Check the moving envelopes of the part and grippers throughout the path. A layout drawing that shows only pickup and drop-off positions can miss interference between them.
Define which signals confirm blank separation, successful pickup, correct placement, and transfer clearance. Then agree on what happens when a part is missing, misplaced, or left in a station after a stop. A restart test should establish how the line identifies occupied stations and returns to synchronized production. Recovery time and restart scrap matter when estimating usable output across a shift.
Send each supplier the same part data, production assumptions, and acceptance criteria. Ask for the proposed station sequence, equipment scope, layout, and any assumptions that affect the quoted production rate. Include these inputs in the RFQ:
Part and material. Provide the drawing revision, 3D model where available, sheet grade, thickness range, finish, and critical dimensions.
Forming sequence. Share the proposed blank and intermediate shapes, expected draw depths, operations, scrap paths, and any known forming defects.
Handling requirements. Identify workpiece weights, surfaces that must remain free of marks, permitted gripping zones, and any required reorientation.
Equipment and site. Provide existing press models if applicable, plant layout, material flow, die-change route, and available space for auxiliaries.
Production and acceptance. State typical batch size, changeover frequency, target accepted parts per hour, trial duration, and measurement criteria.
For a retrofit, separate what the existing equipment can do from what the new transfer and controls must provide. Confirm who will verify press drawings, controls interfaces, and installation dimensions before the proposal is finalized.
Define the trial around production material, the intended handling setup, and an agreed run duration. Track critical dimensions and cosmetic defects alongside transfer faults, scrap, and stop recovery. Report both the running stroke rate and the accepted output over elapsed time so the two figures can be compared.
For example, a line that produces one part per stroke at 12 strokes per minute has a theoretical running rate of 720 parts per hour. If it runs for 50 minutes in an elapsed hour and 95% of the 600 parts produced are accepted, the observed output is 570 accepted parts for that hour. Use the same measurement window and acceptance criteria when comparing line proposals.
A tandem line is worth evaluating when stations need different press capabilities or when the dies and handling paths are difficult to fit under one slide. A single multistation press may suit the job if the stations fit and their force, energy, timing, and clearance requirements can be met together.
Start with the forming load and its position through the stroke, then check energy at the intended speed and permissible off-center loading. Confirm die space, stroke, transfer clearance, and any cushion or ejector requirements against the proposed layout.
Check the shape, weight, center of gravity, stiffness, and permitted contact areas of the part at pickup. Verify grip stability and clearance through the planned motion, using representative workpieces where possible.
It may be possible if the presses have adequate die and transfer clearance and their controls can be integrated with the handling system. Review the exact press models, station spacing, part geometry, and stop-and-restart behavior before selecting equipment.
The constraint can be forming time, press energy, blank feeding, gripper travel, part settling, or unloading. Measure accepted output over a representative run and log the causes of stops to identify where the line loses production time.
Planning a new stamping line or automating an existing one? Discuss your transfer press line with KINGLAN. Share the part drawing, sheet material and thickness, forming sequence, target accepted output, and available floor space. For a retrofit, include the press models, station spacing, and current handling bottleneck.