BLOGS DETAIL
Home / Blogs / How To Prevent Wrinkling And Cracking in Deep Drawing

How To Prevent Wrinkling And Cracking in Deep Drawing

Views: 0     Author: Site Editor     Publish Time: 2026-11-18      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
sharethis sharing button
How To Prevent Wrinkling And Cracking in Deep Drawing

To prevent wrinkling and cracking in deep drawing, control how much sheet metal flows into the die at each location. A wrinkled flange may need more local restraint, while a thinning wall or split corner may need more material to flow in. If both defects appear on the same part, map where each starts before changing blank holder force across the entire die.

The quickest way to narrow down these deep drawing defects is to identify the first operation where they appear, measure how far the blank edge moves inward, and check the remaining wall thickness near critical radii. Together, these observations show whether to investigate blank position, restraint, tooling geometry, lubrication, or the sheet itself.

Diagnose the Defect Before Adjusting the Die

Start by inspecting the part immediately after drawing and again after any redraw, trimming, or flanging operation. A crack found at final inspection may have started as a thin band in the first draw. It may also have started at a cut edge during a later operation. Those two failures require different checks.

Use the same reference points on each trial blank to measure draw-in, the distance the blank edge moves toward the die opening. Mark the defect on a part sketch and compare draw-in and thickness at the affected zone with a sound zone or a previously accepted run. Record the material lot and which side of the blank faces the tooling.

What you see

What to inspect first

What to measure

Waves in the remaining flange

Blank holder contact, blank position, and local restraint

Draw-in and wrinkle location around the flange

A fold or wave in the drawn wall

Whether a flange wrinkle enters the die, or the wall buckles during forming

The stage at which the wave first appears and how far it extends

A split near the punch radius or in the wall

Local thinning, tight radii, friction, and restricted material flow

Minimum thickness and draw-in near the split

A crack starting at a trimmed or pierced edge

Cut-edge condition, burr direction, and edge stretching during the next operation

Crack origin, edge condition, and the operation that opens the crack

KINGLAN progressive stamping die assembly

Prevent Wrinkling by Controlling Local Sheet Flow

Check blank holder contact before raising force

As the flange moves inward, the sheet is compressed around the die opening. If it can buckle out of plane, wrinkles can form. A blank holder supports the flange while allowing material to feed into the cavity. On a part that wrinkles on one side only, check blank centering and holder contact before increasing the force setting. A gap, uneven contact, or a setup difference can leave one zone poorly restrained even when the overall setting looks correct.

KINGLAN compound stamping die assembly

If the holder contacts the sheet as intended, test a controlled change within the approved tooling and press limits. Measure draw-in and minimum wall thickness after the change. A smoother flange can come at the cost of a thinner wall, especially near a corner that already had limited material flow.

Tune draw beads and blank shape by zone

Draw beads add local resistance as the sheet passes through them. That makes them useful when a straight side feeds too freely while a nearby corner needs more material. Review bead engagement and the blank outline together. Changing the blank outline can redistribute material around the die and reduce the need for extra restraint in some areas.

Use the finished trim line when judging the result. A shallow wave outside that line may be acceptable if it remains stable and clears the tooling. A fold that travels into the retained wall can affect dimensions and surface quality even if the outer flange will be trimmed away.

Prevent Cracking by Reducing Local Strain

Check the punch and die radii for wall splits

When a crack appears in the wall or around the punch radius, measure thickness on both sides of the split and inspect earlier trial parts for a thin band in the same location. A tight die entry radius, excessive bead restraint, or inconsistent lubrication can limit how much sheet reaches the wall. A tight punch nose radius can concentrate strain near the transition between the bottom and the wall.

Check the tool surface for scoring or material pickup, and verify that lubricant reaches the affected zone consistently. Compare material grade, thickness, coating, and rolling direction with the conditions used during tryout. If a problem begins after a material lot changes, compare blanks from the two lots under the same setup before altering the tooling. If the part still thins beyond the drawing requirement, evaluate a revised radius where the part design permits it, a different blank shape, or an additional draw operation.

Investigate the cut edge when the crack starts there

A crack that starts at a pierced hole or trimmed edge during flanging may be an edge stretch problem. Inspect the edge before forming and compare the crack origin with the location of the burr or damaged cut surface. Check punch and die wear, cutting clearance, and whether the burr faces the tensile side of the subsequent bend.

If the crack follows a change in the trimming tool or material lot, reproduce that condition during the trial. For sensitive grades, ask whether a representative edge stretch test or a trial with a different edge preparation is appropriate. A wall-thickness check remains useful, but it cannot establish the condition of the cut edge.

Validate Settings That Prevent Both Defects

Establish a repeatable operating range

When a straight flange wrinkles and a nearby corner splits, treat the two areas separately. Check whether the straight section needs more restraint and whether the corner needs more feed. A single increase in blank holder force can make the flange look better while worsening the split. Use the defect map and draw-in measurements to decide whether to adjust local bead engagement, blank shape, or holder contact.

Run a baseline with representative production sheet. Record blank position, lubrication, holder or cushion settings, press speed, draw-in, and minimum thickness. Change one major factor at a time where practical. Once a setting looks promising, repeat the run at the intended production speed. Inspect parts at intervals because tool temperature, lubricant coverage, and material pickup can change as the run continues.

Verify the press, cushion, and tooling as a system

If the setup uses a die cushion, check the available force and travel against the die requirements. Review how the force is applied through the stroke and transferred to the holder. For an existing machine, send the press model and cushion specifications along with the tooling drawings. KINGLAN’s press maintenance page discusses die cushions for deep drawing, and its ALM Series battery case press provides an example of equipment for multistation forming.

KINGLAN ALM Series press for battery case production

Before accepting the process, agree on the locations for thickness readings, which surfaces must remain free of wrinkles or marks, and how the part will be inspected after trimming. Also record the material specification and setup used for accepted parts so the production team can reproduce the result.

Frequently Asked Questions

Does increasing blank holder force always prevent wrinkles?

It can help when insufficient restraint is causing the flange to buckle. Check blank position and holder contact first, particularly if wrinkles appear on one side. After increasing force, recheck draw-in and wall thickness near the punch radius and corners.

Why does a deep-drawn part wrinkle and crack at the same time?

Different areas can experience different material flow. One section may feed too freely and buckle, while a nearby corner receives too little material and stretches until it splits. Map both defects and compare draw-in by zone before changing the overall force setting.

Can lubrication reduce cracking in deep drawing?

Consistent lubrication can reduce friction and improve material flow where the sheet passes over a radius or through a bead. If the crack begins at a damaged cut edge or at a tight punch radius, inspect that feature as well and verify the result with thickness readings or an edge-focused trial.

When should I add a second drawing operation?

Evaluate a redraw when a single draw repeatedly fails the minimum wall-thickness requirement or splits at the target depth after material flow, tooling radii, and lubrication have been reviewed. Include how the intermediate shell will be supported and located at the next station.

What data should I collect before requesting technical support?

Collect the part drawing, material grade and thickness, blank dimensions, forming sequence, press and cushion details, and photos of the defects. Identify the first station where the problem appears and provide any draw-in and thickness readings from accepted and rejected parts.

If your drawn parts keep wrinkling or cracking, discuss your deep drawing application with KINGLAN. Share your part drawing, blank dimensions, sheet grade and thickness, press and cushion details, and photos showing where the defect starts. Include draw-in or wall-thickness readings if available.

Tel: +86-15857957798
Fax: +86-21-5410-8802
Add: No 19, Huanglong 3rd Road, Huanglong Industrial Zone, Wuyi, Zhejiang, China
Leave a Message
Online Message

Quick Links

Products

About

Copyright © 2024Zhejiang Jinaolan Machine Tool Co., Ltd. All Rights Reserved.
Privacy Policy | SiteMap | Support By Leadong