BLOGS DETAIL
Home / Blogs / How Deep Drawing Dies Work in Sheet Metal Forming

How Deep Drawing Dies Work in Sheet Metal Forming

Views: 0     Author: Site Editor     Publish Time: 2026-11-13      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
sharethis sharing button

A deep drawing die turns a flat sheet metal blank into a hollow part by drawing material inward as the punch moves into the die opening. The punch shapes the part, the die radius guides the sheet into the opening, and the blank holder controls how much material can flow inward. The goal is to feed enough metal into the wall to avoid excessive thinning while keeping the remaining flange from wrinkling.

The same principle applies to round cups, rectangular housings, and battery cases. Each shape puts different demands on the tooling. To understand whether a die will work for your part, start by looking at where the sheet needs to move and where it needs to be restrained.

What Does a Deep Drawing Die Do?

The punch and die opening create the part shape

The punch moves relative to the die and pushes the center of the blank into the opening. As the punch travels, material from the outer portion of the blank flows over the die entry radius and into the cavity. This material becomes part of the wall. The punch nose radius forms the transition between the bottom and the wall, where local thinning can become critical.

KINGLAN compound stamping die assembly

The gap between the punch and die must accommodate the sheet as it deforms. In conventional drawing, the flange can thicken in some areas as material moves inward. If the gap is too tight for the actual material and thickness variation, it can increase load, cause surface marks, or reduce wall thickness. Some processes deliberately use a separate ironing operation to thin the wall. That requirement should be specified when the tool is designed.

The blank holder controls the flange

The blank holder, sometimes called a binder, presses the sheet against the die face around the opening. During drawing, the flange is pulled inward and compressed around its circumference. If the sheet has too much freedom to buckle, wrinkles can develop. If the blank holder restricts movement too much, the wall must stretch more to reach the required depth, increasing the risk of thinning or splitting.

On some presses, a die cushion supplies the blank holder force through the tooling. Larger or irregular parts may also use draw beads to add restraint in selected areas. A rectangular housing, for example, can need different restraint along its straight sides and around its corners. The objective is to control where material enters the die throughout the stroke.

How the Sheet Moves Through a Drawing Stroke

From a flat blank to a formed shell

  1. Locate the blank. Position the sheet using the tooling locators or loading system. Blank position affects how much material is available on each side of the part.

  2. Engage the blank holder. Apply the planned restraint before significant drawing begins. The holder keeps the flange under control while allowing it to move.

  3. Draw the part. Move the punch relative to the die opening. The flange feeds inward over the die radius, and the wall takes shape as the stroke progresses.

  4. Release and remove the part. Retract the tooling and strip or eject the shell. Send it to another draw station or to trimming, piercing, or flanging as required.

During a trial, record how far the blank edge moves inward at several points around the die. This movement is called draw-in. If one corner consistently pulls in less than its opposite corner, check blank location, lubrication, and local restraint. Measure wall thickness at the same time. Two trial parts can look similar from the outside and have different minimum thicknesses near a critical radius.

When to use a redraw station

A first draw creates the initial shell. A redraw can reduce its cross-section and increase its depth or bring the shell closer to the final geometry. The required sequence depends on the sheet grade, starting blank, radii, target depth, and allowable thinning. For round cups, the ratio of blank diameter to punch diameter provides a first screening measure. Rectangular and irregular parts also require attention to corner flow and local strain.

KINGLAN progressive die for sheet metal stamping

A multistation route needs a way to move and locate the intermediate shell at every operation. A progressive layout can be evaluated if the carrier allows the material to flow and the part remains stable. Transfer tooling is worth evaluating if the shell needs to move independently. KINGLAN lists drawing among the possible operations in its progressive die tooling. Its ALM Series battery case press is an equipment example for multistation production.

KINGLAN ALM Series press for battery case production

Diagnose Common Deep Drawing Defects

The location of a defect often tells you more than the defect name alone. Mark where it appears, identify the first operation that produces it, and record the material lot and setup conditions before adjusting the die.

Defect

What to inspect first

What to verify during the trial

Flange wrinkles

Blank holder force and contact, blank size, and local draw bead restraint

Whether the flange stays stable while still feeding enough material into the wall

Splits or excessive thinning

Punch and die radii, local restraint, lubrication, and material grade

Minimum wall thickness and the location where the split or necking begins

Scratches or scoring

Tool finish, transferred material on contact surfaces, and lubricant coverage

Whether marks recur at the same point and worsen as the die runs

Uneven rim height or earing

Blank centering, sheet rolling direction, and material variation

Whether the high points repeat in a pattern and how much trim allowance is needed

Adjust one major variable at a time where practical. Increasing blank holder force may reduce wrinkling while increasing thinning elsewhere. Adding lubricant may improve flow in a tight corner while changing draw-in along an adjacent wall. Keep a record of the setting, measured draw-in, and minimum thickness after each adjustment. That record helps distinguish a workable production window from a setting that produced one acceptable sample.

Specify the Die and Press for Production

Define the tooling and press requirements together

Send the finished part drawing and the sheet specification before asking for a die design. Mark the areas that have minimum wall thickness, tight dimensional requirements, or visible surfaces. If trimming will remove the drawn flange, specify which dimensions apply before and after trimming. If the supplier is expected to develop the blank and redraw sequence, make that part of the quotation scope.

For an existing press, supply its model, stroke, usable die space, and any cushion details. Ask the supplier to check available force at the point in the stroke where drawing occurs, available energy at the intended running speed, and the cushion force and travel required. Also agree on how the part will be loaded and ejected and how a partially formed shell will be located at the next station.

Define what a successful die trial looks like

A useful trial checks repeatability with representative production sheet. Agree on the sample size or run duration and record the following:

  • Part quality: Finished dimensions, minimum wall thickness at agreed locations, cracks, wrinkles, and surface marks.

  • Material flow: Draw-in at reference points and rim variation before trimming.

  • Tool and press settings: Blank holder or cushion settings, lubricant, and running speed.

  • Production behavior: Reliable loading and ejection, recurring defects, and accepted output over the trial.

Ask for samples taken at intervals through the run. A setup may produce good parts at the start and begin scoring after material builds up on a contact surface. Checking parts over time gives the buyer a stronger basis for acceptance and provides the production team with settings to reproduce.

Frequently Asked Questions

What is the difference between a deep drawing die and a bending die?

A deep drawing die pulls material inward from the flange to form a hollow part with a bottom and walls. A bending die changes the angle of a sheet along a bend line. A finished part can require both operations at different stages.

Why does the sheet split near the punch radius?

The area near the punch radius can thin as it transmits the force needed to draw the flange inward. Check whether the radius is too tight, the blank holder or draw beads restrict flow too much, or lubrication is inconsistent. Measure thickness around the radius to locate where thinning begins.

Does every deep drawing die need a separate blank holder?

The need for a separate holder depends on the part geometry and the risk of buckling. Some shallow or suitably proportioned parts may be drawn without a separate holder. If the flange wrinkles or draw-in is uneven, evaluate how the process will control material flow.

How do you decide whether a part needs more than one draw?

Review the finished geometry, sheet properties, corner radii, and minimum wall thickness. Use an initial drawability assessment to propose the sequence, then confirm it with forming analysis or a die trial using representative material.

What should I provide when requesting a deep drawing die quote?

Provide the part drawing, 3D model if available, material grade, thickness, and expected production volume. Mark critical radii, minimum wall thickness, cosmetic surfaces, and any operations after drawing. If you plan to use an existing press, include its model, stroke, die space, and cushion details.

Planning tooling for a drawn housing, cup, or case? Discuss your deep drawing project with KINGLAN. Share the part drawing, sheet grade and thickness, production volume, and available press details. If you are troubleshooting an existing tool, include photos of the defect and identify the first station where it appears.

Tel: +86-15857957798
Fax: +86-21-5410-8802
Add: No 19, Huanglong 3rd Road, Huanglong Industrial Zone, Wuyi, Zhejiang, China
Leave a Message
Online Message

Quick Links

Products

About

Copyright © 2024Zhejiang Jinaolan Machine Tool Co., Ltd. All Rights Reserved.
Privacy Policy | SiteMap | Support By Leadong